Alexor WT5500-433 Installation Manual download pdf

English

WAR NING:

Please refer to the System Installation Manual for information on limitations regarding product use and function, and information on the limitations as to liability of the manufacturer.

These instructions are to be used in conjunction with the appropriate Control Panel Installation Manual, with which this equipment is intended to be used.

This Installation Sheet applies to the following models: WT5500-433 / WT5500-868 / WT5500P-433 / WT5500P-868.

Operating Instructions shall be made available to the user.

Do not dispose the waste battery as unsorted municipal waste. Consult your local rules and /or laws regarding recycling of this battery, it will help protect the environment by reducing the number of batteries

consumed. Some of the materials that are found within the battery could become toxic if not disposed properly and/or may affect the environment, and indirectly everybody’s health.

WT5500 Installation Instructions

System is

Ready to Arm

Function

Keys

LED Indicators

Ready

Armed

Trouble

AC Power

Scroll Keys

Ambient Light

Sensor

LCD

Emergency Keys

Fire

Auxiliary

Panic

< > indicates user can

scroll through options

DG009033

29007335R001

Enrolling the Keypad

The WT5500 must be configured in tandem with the PC9155 in order for the

system to function as desired.

1. Turn on the PC9155. The panel will be alert to any keypad enrollment

activity for a period of two minutes. Note that the PC9155 Ready and AC

LEDs will be flashing for this two-minute period.

2. A WT5500 must be turned on during this two-minute period for it to be

assigned to the PC9155.

3. Simultaneously press and hold [

] and [1]; by doing so you force the key-

pad to broadcast its ESN (Electronic Serial Number).

4. When the keypad has been successfully enrolled - this should take less

than 5 seconds - on the system, the message ‘Enrollment Successful’ will

be displayed on the keypad LCD for five seconds. The Ready and AC LEDs

will return to their previous state.

5. Repeat steps 3 and 4 on each additional keypad to be enrolled.

Programming Labels

1. Use this section to assign a meaningful name (e.g. Front Door, Hall-

way, etc.) to each zone.

2. Enter keypad programming by pressing

[][8][Installer Code][].

Enter the 3-digit section number for the label to be programmed.

3. Use the arrow keys (<>) to move the cursor underneath the letter to

be changed.

4. Press the number keys 1 through 9, corresponding to the letter you require.

For example, pressing number key 2 once will display the letter D; pressing

it again will display the letter E; pressing it a third time will display the let-

ter F, and so on.

5. When the required letter or number is displayed use the arrow keys (<>)

to scroll to the next letter.

6. When you are finished programming the Zone Label, press [

]. Scroll to

‘Save’ and press [] again.

7. Repeat Steps 2 through 5 until all Labels are programmed.

ASCII Characters

Broadcasting LCD Labels

LCD programming is done using the keypad. If more than one LCD keypad is

present on the system, labels programmed at one keypad can be broadcast

to all other LCD keypads. Perform the following in order to broadcast labels:

1. Program one LCD keypad completely.

2. Enter keypad programming by pressing [

][8][Installer Code][] at the

keypad that was programmed.

3. Enter Section [998]. The keypad will broadcast the label programming to

the PC9155. The PC9155 will then broadcast the label information to other

WT5500 keypads that have been enrolled by way of 2-way wireless.

NOTE: This operation may take several minutes.

4. When the keypad is finished press the [#] key to exit.

NOTE: Label broadcast from this keypad is only compatible with

other WT5500 keypads.

Changing Brightness/Contrast

1. Press [][6] [Master Code].

2. Use the arrow keys (<>) to scroll to Brightness or Contrast Control.

3. Press [

] to select the setting you want to adjust.

4. Brightness Control: There are multiple backlight levels. Use the arrow keys

(<>) to scroll to the desired level. Press [] to select.

5. Contrast Control: There are four different display contrast levels. Use the arrow

keys (<>) to scroll to the desired contrast level. Press [



] to select.

6. To exit, press [#].

NOTE: During battery operation, the keypad uses the ambient light

sensor to automatically adjust the backlighting brightness lev-

els in order to conserve battery life.

Changing the Buzzer Level

1. Press [][6] [Master Code].

2. Use the arrow keys (<>) to scroll to Buzzer Control. Press [

] to select.

3. Use the arrow keys (<>) to scroll to the desired buzzer level among

the 21 available selections. Press [

] to select.

4. To exit, press [#].

Keypad LED Symbols

Proximity Tags (WT5500P only)

You can use the proximity tag to perform any keypad function that would

normally require a user access code. Simply present the tag to the target icon

or to the left of the Keypad LCD.

Enrolling proximity tags

Enrolling a tag with one keypad will enroll it automatically to all WT5500P

keypads enrolled on the system.

1. Enter [][5][Master Code]. You will enter the

User Code Edit Select

menu.

2. Enter a two-digit User Code slot (01-16, 40) to be associated with the

proximity tag. Alternatively, scroll to the two-digit user number and press

the [

] key. You will enter the

New Code Edit

menu.

3. Enter the four- or six-digit New Code. The LCD will prompt you to swipe

your proximity tag. Otherwise, press the [#] key to exit.

4. Present your proximity tag to the keypad. If enrollment is successful,

acknowledgement beeps will sound and the keypad LCD will read ‘Tag

Enrolled Successfully’. If the proximity tag has been enrolled previously, an

error tone will sound. The LCD will read ‘Duplicate Tag/User Code’.

5. The keypad will return to the

User Code Edit Select

menu.

Deleting proximity tags

Delete the prox tags from the system when they are lost or no longer needed.

1. Enter [][5] [Master Code] on the keypad.

2. Enter or select the User Code slot you wish to delete. You will enter the

User

Code Edit Select

menu.

3. Press [

] to delete both the user code and the proximity tag.

NOTE: User code can only be deleted individually.

NOTE: User 40 - Master Code cannot be deleted; a deletion attempt

on this user code will delete the proximity tag only.

NOTE: A user code, once deleted, must be re-enrolled before it can

be used again.

[1] - A, B, C, 1 [4] - J, K, L, 4 [7] - S, T, U, 7 [0] - Space

[2] - D, E, F, 2 [5] - M, N, O, 5 [8] - V, W, X, 8

[3] - G, H, I, 3 [6] - P, Q, R, 6 [9] - Y, Z, 9,0

Symbol Description

Ready Light (green)

If the Ready light is on, the system is ready for

arming.

Armed Light (red)

If the Armed light is on, the system has been

armed successfully.

System Trouble (yellow) Indicates that a system trouble is active.

AC (green) Indicates that AC is present at the keypad.

The complete R&TTE Declaration of Conformity can be found at

http://www.dsc.com/listings_index.aspx.

The WT5500 Wire-Free Keypad is designed to work with the PC9155 Wire-

less Panel. Since the PC9155 is mounted in a secure location within the

home, the WT5500 is the main interface to the system.

Specifications

Unpacking

The WT5500 keypad package is available in five distinct configurations,

Wall mount, Wall mount w/Proximity, Desk Stand, Accessory Kit and Proxim-

ity Tags Only. The contents of each are described below.

Mounting

You should mount the keypad where it is accessible from designated points

of entry and exit. Once you have selected a dry and secure location, perform

the following steps to mount the keypad.

Wall Mounting Plate

1. Locate the screw holes (4) at each corner of the mounting plate.

2. Use the four screws provided to affix the mounting plate to the wall, ensure

the mounting tabs are facing you (see above diagram).

3. Align the four mounting slots in the WT5500 housing with the four mount-

ing tabs protruding from the mounting plate.

4. Slide the keypad into place.

5. Firmly but carefully snap the keypad down onto the mounting plate.

6. To fasten the keypad more securely onto the mounting plate, locate the

two screw holes in the bottom of the mounting plate then using the two

screws provided in the hardware pack, screw the keypad into place.

Desk Stand - WT5500D

1. Insert the four rubber feet

(found in the hardware pack)

into the indentations provided

in the bottom of the desk stand.

2. Place the desk stand on a

secure, uncluttered surface.

3. Align the four mounting slots in the WT5500 housing with the four mount-

ing tabs protruding from the desk stand.

4. Slide the keypad into place. Firmly but carefully snap the keypad down

onto the desk stand.

5. To fasten the keypad securely onto the desk stand, locate the two holes in

the top corners of the back of the desk stand, then using the two screws

provided screw the keypad to the desk stand.

Apply Battery Power

1. Slide the keypad up and out from the mounting plate/desk stand (remov-

ing the screws first if required). The bay for the four AA batteries is open

and visible at the back of the keypad.

2. Insert the batteries as directed on the back of the keypad. Ensure the cor-

rect polarity is observed.

3. Replace the keypad on the mounting plate / desk stand.

Apply AC Power

1. Slide the keypad up and out from the mounting plate / desk stand.

2. Locate the power adaptor jack at the back of the keypad housing.

3. Place the adaptor plug in the housing indentation, perpendicular to the

keypad. Insert the adaptor plug firmly into the jack.

4. Pivot the adaptor plug downwards so that it fits flush with the housing.

Guide the AC wire along the channel provided in the keypad housing; the

wire will finally extend through the bottom of the housing.

5. Replace the keypad on the mounting plate/desk stand (in the latter case, a

further channel is provided in the bottom of the desk stand. Guide the AC

wire along this channel; the wire will finally extend through an opening in

the back of the stand).

6. Plug the adaptor into a wall outlet.

NOTE: Only use the power adaptor (4.5VDC, 0.5A, 2.25W) supplied

with the kit.

CAUTION: The socket-outlet in which the direct plug-in adaptor is

inserted, must be close to the keypad and easily accessible. The

plug of the adaptor serves as a means of disconnection from the

supply mains.

Programming the Keypad

here are several programming options available for the keypad (see below).

Programming the keypad is similar to programming the rest of the system. To

turn an option on/off, press the number corresponding to the option on the

number pad. The numbers of the options that are currently turned on will be

displayed along the top of the LCD. For information on programming the rest

of your security system, please refer to your system’s Installation Manual. A

maximum of four keypads can be on the system at any one time.

Language Programming

Hold the (<>) keys for 2 seconds to enter language programming. Scroll

to the desired language and press [] to select.

If Section 075, Option 4 is turned off, language programming can

only be performed while in installers programming.

Installation Instructions

Temperature range: -10°C to +55°C (14°F to 131°F), Temperature range for

UL/ULC: 0°C to +49°C (32°F to 120°F)

Humidity (MAX): 93%R.H.

Plastic enclosure protection degree: IP30, IK04

Power Adaptor Output Voltage: 4.5VDC @ 0.5A

Models - US/Latin America: SA103A-0506-6U; Canada: SA103A-0506-6; EU:

SA103A-0506G-6; UK: SA106C-05BS; AUS./NZ: SA106C-05AS;

China: SA106C-05HS.

Battery: 4 AA, 3V, Energizer Alkaline

WT5500 Current draw: 50mA

Wall-mount tamper

5 programmable function keys

Ready (Green LED), Armed (Red LED), Trouble (Yellow LED), AC (Green LED)

Frequency: 433.92MHz (WT5500-433/WT5500P-433 only)

Frequency: 868.35MHz (WT5500-868/WT5500P-868 only)

WT5500 - WALL MOUNT WT5500DMK - ACCESSORY KIT

• 1 WT5500 Keypad • 1 WT5500DMK Keypad

• 1 WT5500BRK Wall Bracket • 1 Hardware Pack

• 1 Installation Manual • 1 Power Adaptor

• 1 Inner Door Sticker

• 4 AA Batteries

WT5500P - WALL MOUNT/PROX TAG

• 1 Hardware Pack • 1 WT5500P Keypad

• 1 WT5500BRK Wall Bracket

WT5500D - DESK STAND • 1 Installation Manual

• 1 WT5500 Keypad • 1 Inner Door Sticker

• 1 WT5500DMK Desk Stand • 4 AA Batteries

• 1 WT5500BRK Wall Bracket • 1 Hardware Pack

• 1 Installation Manual

• 1 PT4 or PT8 Prox Tag (433MHz/868MHz)

• 1 Inner Door Sticker

• 1 Power Adaptor PROXIMITY TAGS ONLY

• 4 AA Batteries

• 1 PT4 or PT8 Prox Tag (433MHz/868MHz)

• 2 Hardware Packs • 1 Installation Manual

Mounting

Tabs

DG009049

Screw

Holes

Screw

Holes

Screw

Holes

Screw

Holes

DG009096

DG009048

Mounting

Holes

Mounting

Holes

Batteries

Plug

Wire

Channel

Tamper

Switch

NOTES:

System is

Ready to Arm

DG009153

Prox Tag

Reader

1 2

Summary of Contents

Page 1 - Ready to Arm

EnglishWAR NING: Please refer to the System Installation Manual for information on limitations regarding product use and function, and information on

Page 2 - Keypad Programming

Keypad Function Key ProgrammingEnter keypad programming by pressing [4][8][Installer Code][4][000]. Press 1 through 5 for individual function key pro

Comments to this Manuals

No comments

Alexor WT5500-433 Installation Manual

Browse online or download Installation Manual for Security access control systems Alexor WT5500-433. Alexor WT5500-433 Installation manual User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Security access control systems Alexor WT5500-433